Open topic with navigation

Calculation stiffness of 1D element

Members which are not expected to be loaded above the level which would cause the tensile strength of the concrete to be exceeded anywhere within the member should be considered to be uncracked. Members which are expected to crack, but may not be fully cracked, will behave in a manner intermediate between the uncracked and fully cracked conditions. New stiffness (stiffness with taking into account cracking) is calculated in centre of each 1D element.

Two types of stiffness are calculated:

Short-term stiffness - is calculated using 28 days modulus of elasticity E_c = E_cm, it follows that value of stiffness is loaded directly from properties of the concrete material

Long-term stiffness - is calculated using effective E modulus based on creep coefficient for acting load, it follows E_c = E_c,eff = E_cm/(1+j).

Calculation effective modulus of elasticity is based on equation 5.27 in EN 1992-1-1, but instead of effective creep coefficient j_ef, only creep coefficient j is used

The following procedure is used for calculation stiffens for

• calculation transformed Css characteristics of uncracked section (Ai, Ii, ti...)

• calculation stiffness’s of uncracked cross-section ((EIy)_I,( EIz)_I, (EA)_I) to centre of uncracked transformed cross-section

• calculation maximum value of tensile stress of uncracked cross-section (value s_ct,res) for respective characteristic combination (N_char,res,M_char,res,y, M_char,res,z)

• calculation maximum value of tensile stress of uncracked cross-section (value s_ct,imm) for immediate characteristic combination (N_char,im,M_char,im,y, M_char,im,z)
• check condition s_ct≥s_ct,imm,.
  • If condition is fulfilled, then respective characteristic combination will be used for calculation, N_char=N_char,res,M_char,y =M_char,res,y, M_char,z=M_char,res,z,s_ct=s_ct,res
  • otherwise immediate characteristic combination will be used N_char=N_char,im,M_char,y =M_char,im,y, M_char,z=M_charim,z,s_ct=s_ct,im

• check condition(sct <= scr)

  • If condition is fulfilled, then cross-section is uncracked nad

    • bending stiffness around y-axis EI_y = (EIy)_I

    • bending stiffness around z axis EI_z = (EIy)_I

    • axial stiffness EA = EA_I,

  • Else , cross-section is cracked and average stiffness will be calculated

• calculation transformed Css characteristics of cracked section (Air, Iir, tir...)
• calculation stiffness’s of fully cracked cross-section ((EIy)_II,( EIz)_II, (EA)_II) to centre of cracked transformed cross-section
• calculation stress in tensile reinforcement of fully cracked cross-section (value s_sr)for characteristic combination (N_char,M_char, M_char,z)
• calculation stress in tensile reinforcement of fully cracked cross-section (value s_s)for respective combination (N,M_y,M_z

• calculation the distribution coefficient zaccording equation 7.19 in EN 1992-1-1

  

  where bis coefficient taking account of the influence of the duration of the loading or of repeated loading on the average strain (b=1 for calculation short-term stiffness, b=0,5 for calculation long-term stiffness)

• calculation averages value of stiffness’s based on equation 7.18 in EN 1992-1-1

  • bending stiffness around y-axis (EIy) = 1/[z/(EIy)_II + (1-z)/ (EIy)_I]

  • bending stiffness around z-axis (EIz) = 1/[z/(EIz)_II + (1-z)/ (EIz)_I]

  • axial stiffness (EA) = 1/[(z/(EA)_II + (1-z)/( EA)_I],

Stiffness is recalculated to principal axis for unsymmetrical cross-section

The four type of stiffnesses is calculated for each 1D element and each dangerous combination:

The following stiffnesses are changes in stiffness matrix for 1D element:

EA_x =EA

GA_y=GA_z = G×EA_x/(1.2×E_c)

EI_y =EIy

EI_z =EIz

GI_x=0.5×(1-m)×(EI_y×)EI_z)^0.5

where

G is shear modulus of the concrete calculated according to formula G = 0.5×E_c/(1+m)

m is Poisson coefficient of the concrete loaded from material properties of the concrete

Eccentricity of stiffnness (distance between centre of gravity of concrete cross-section and centre of gravity of cracked transformed cross-section) is not taken into account in current version

Open topic with navigation